اشکان فروتن
مدیر بازنشسته
دموی یک سری برنامه رو براتون میذارم ، البته چند تاشو قبلا" بچه ها گذاشتن ولی دوباره و در کنار هم براتون میذارمش . . .
Demo ی یک سری برنامه
- شروع کننده موضوع اشکان فروتن
- تاریخ شروع
اشکان فروتن
مدیر بازنشسته
The Energy Analyst
THE ENERGY ANALYST is a series of twenty-six sophisticated, engineering programs for the engineer who specifies, operates, or
tests power plant components or evaluates energy alternatives. For more than 10 years, more than 2000 users have attested to the
power and professionalism of these programs. And now with a complete conversion to the Windows format, each program has a
friendlier, interface that will get you running in no time. The data handling techniques make your job easier, and although
documentation is provided, it is seldom needed because the "fill-in" forms lead you by the hand at each step of the analysis The
input data and the results can be printed with a single command and are in a form ready for inclusion in your final reports.
The Energy Analysis Demonstration Programs
The Energy Analyst is a collection of 26 separate programs, of which there are numerous demonstration program. These are listed
below. Feel free to download any or all of them!
Cogeneration Economics (1.9 MB) Download
http://www.cuservices.net/DemoDownloads/CogenDemo.exeCombustion Analysis (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/CombustDemo.exeGas Compressor (3.3 MB) Download
http://www.cuservices.net/DemoDownloads/CompressorDemo.exeDuct Design (3.4 MB) Download
http://www.cuservices.net/DemoDownloads/ductdemo.exeGas Expander (6.4 MB) Download
http://www.cuservices.net/DemoDownloads/ExpanderDemo.exeFlash Tank Economics (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/FlashTankDemo.exeGas Turbine (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/gtdemo.exeShell and Tube Heat Exchanger (4.4 MB) Download
http://www.cuservices.net/DemoDownloads/HtExchDemo.exeInsulation Economics (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/InsulDemo.exeNozzle and Orifice Flow (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/NozzleDemo.exePipe Network (Hardy Cross) (6.1 MB) Download
http://%20http//www.cuservices.net/DemoDownloads/PipeNetworkDemo.exePsychrometrics (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/PsychDemo.exeCentrifugal Pump (7.4 MB) Download
http://www.cuservices.net/DemoDownloads/pumpdemo.exeSteam Turbine (9.4 MB) Download
http://www.cuservices.net/DemoDownloads/SteamTurbDemo.exeSurface Condenser (1.7 MB) Download
http://www.cuservices.net/DemoDownloads/SurfaceCondenserDemo.exeCooling Tower (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/TowerDemo.exe~
Energy Conversion - Version A
Engineering Software has developed a new Windows based software package, Energy Conversion, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species, contains coefficients for the calculation of
physical properties -- the user has the capability to use the coefficients to carry out independent engineering calculations involving
physical properties of various species, steam approximations for both saturated and superheated areas, analyzes power cycles,
power cycle components/processes and compressible flow.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~~
Energy Conversion - Version B
Engineering Software has developed a new Windows based software package, Energy Conversion, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species, steam approximations for both saturated
and superheated areas, analyzes power cycles, power cycle components/processes and compressible flow.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
THE ENERGY ANALYST is a series of twenty-six sophisticated, engineering programs for the engineer who specifies, operates, or
tests power plant components or evaluates energy alternatives. For more than 10 years, more than 2000 users have attested to the
power and professionalism of these programs. And now with a complete conversion to the Windows format, each program has a
friendlier, interface that will get you running in no time. The data handling techniques make your job easier, and although
documentation is provided, it is seldom needed because the "fill-in" forms lead you by the hand at each step of the analysis The
input data and the results can be printed with a single command and are in a form ready for inclusion in your final reports.
The Energy Analysis Demonstration Programs
The Energy Analyst is a collection of 26 separate programs, of which there are numerous demonstration program. These are listed
below. Feel free to download any or all of them!
Cogeneration Economics (1.9 MB) Download
http://www.cuservices.net/DemoDownloads/CogenDemo.exeCombustion Analysis (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/CombustDemo.exeGas Compressor (3.3 MB) Download
http://www.cuservices.net/DemoDownloads/CompressorDemo.exeDuct Design (3.4 MB) Download
http://www.cuservices.net/DemoDownloads/ductdemo.exeGas Expander (6.4 MB) Download
http://www.cuservices.net/DemoDownloads/ExpanderDemo.exeFlash Tank Economics (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/FlashTankDemo.exeGas Turbine (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/gtdemo.exeShell and Tube Heat Exchanger (4.4 MB) Download
http://www.cuservices.net/DemoDownloads/HtExchDemo.exeInsulation Economics (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/InsulDemo.exeNozzle and Orifice Flow (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/NozzleDemo.exePipe Network (Hardy Cross) (6.1 MB) Download
http://%20http//www.cuservices.net/DemoDownloads/PipeNetworkDemo.exePsychrometrics (3.2 MB) Download
http://www.cuservices.net/DemoDownloads/PsychDemo.exeCentrifugal Pump (7.4 MB) Download
http://www.cuservices.net/DemoDownloads/pumpdemo.exeSteam Turbine (9.4 MB) Download
http://www.cuservices.net/DemoDownloads/SteamTurbDemo.exeSurface Condenser (1.7 MB) Download
http://www.cuservices.net/DemoDownloads/SurfaceCondenserDemo.exeCooling Tower (3.5 MB) Download
http://www.cuservices.net/DemoDownloads/TowerDemo.exe~
Energy Conversion - Version A
Engineering Software has developed a new Windows based software package, Energy Conversion, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species, contains coefficients for the calculation of
physical properties -- the user has the capability to use the coefficients to carry out independent engineering calculations involving
physical properties of various species, steam approximations for both saturated and superheated areas, analyzes power cycles,
power cycle components/processes and compressible flow.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~~
Energy Conversion - Version B
Engineering Software has developed a new Windows based software package, Energy Conversion, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species, steam approximations for both saturated
and superheated areas, analyzes power cycles, power cycle components/processes and compressible flow.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
اشکان فروتن
مدیر بازنشسته
Fluid flow
~~
Piping Pressure Loss
This program calculates the pressure loss of fluids flowing under pressure in circular pipes. The program can calculate flow in
either compressible mode (for gases) or incompressible flow. It allows a choice of units: gpm, pph, scfm, or acfm. Any single-phase
liquid or gas can be accepted. The properties of water, steam and air are built in.
Download
http://www.cuservices.net/DemoDownloads/PlossDemo.exe~
Pipe Network (Hardy Cross)
This program uses the iterative Hardy-Cross algorithm to determine the flow and pressure loss in each leg of a series-parallel pipe
network.
Download
http://www.cuservices.net/DemoDownloads/PipeNetworkDemo.exe~
Processing, Storage Tanks, Pressure Vessels, Mixing Systems
~
CerebroMix
CerebroMix is a unique PC-based program which encompasses all the functionality of the other Cerebro products, CerebroTank,
CerebroPV and CerebroMixLight. It is an indispensable tool for anyone involved in the evaluation and design of mixers in vertical
tanks, either pressurized or atmospheric. Using input data such as primary dimensions, fluid properties and certain desired mixing
objectives, the program will output full operating conditions, critical impeller speeds, liquid level gradation, solid suspension and all
system dimensions.
CerebroMix also allows the analysis of storage and process tanks, vertical or horizontal, pressurized or atmospheric. Using input
data such as principal dimensions, fluid density, material, desired tank shape (including heads) and support type, the software
calculates structural characteristics for both the tank and the support structure using ASME Section VIII, Division 1 and EN 13445
standards.
This software allows users and manufacturers of pressure vessels and mixers to check their equipment for various operating
conditions, in order to provide a full analysis of performance, as well as risk assessment.
The program produces output in the form of a Microsoft Word Document, with all data listed in tabular form, together with a scale
drawing of the tank and its support structure.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
CerebroPV
CerebroPV is an easy-to-use PC program to assist in the evaluation and design of vertical and horizontal storage tanks, running
either pressurized or at atmospheric conditions. Using input data such as principal dimensions, fluid density, material, desired tank
shape (including heads) and support type, the software calculates structural characteristics for both the tank and the support
structure using ASME Section VIII Division 1 standards.This software allows both users and manufacturers of pressure vessels to
check their equipment for various operating conditions, in order to provide a risk assessment. The program produces output in the
form of a Microsoft Word Document, with all data listed in tabular form, together with a scale drawing of the tank and its support
structure.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
CerebroTank
CerebroTank is an easy-to-use PC program to assist in the evaluation and design of vertical and horizontal storage tanks. Using
input data such as geometric dimensions, fluid density, support type, tank material and shape (including heads), the software
calculates structural characteristics for the tank and the supports (legs and saddles). Using the wall thicknesses provided by the
software, the user can select from a database of standard plate thicknesses; these thicknesses will be factored depending on the
degree of corrosiveness of the liquid. The program also gives flange thicknesses for the tank head, allowing for weld efficiency.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
Combustion
~
Enviropak
Enviropak is a combustion calculator and incinerator design package for organics. The user can choose from the resident database
of compounds or define new compounds. Recovery heat exchange, combustor sizing and destruction efficiency are all features of
this powerful software package. Included is a useful combustion properties estimation module. Output includes analysis of
combustion gases with computed temperature and residence times.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Combustion Analysis
This program calculates boiler efficiency using the heat loss method of the ASME Boiler Code PTC-4.1. The program accepts the
ultimate analysis of any fuel, % by weight for liquids and % by volume for gases. It performs a stochiometric analysis of the
combustion and calculates the individual losses, the quantities and types of gases produced, and the air flow required for the given
% excess air.
Download
~~
Piping Pressure Loss
This program calculates the pressure loss of fluids flowing under pressure in circular pipes. The program can calculate flow in
either compressible mode (for gases) or incompressible flow. It allows a choice of units: gpm, pph, scfm, or acfm. Any single-phase
liquid or gas can be accepted. The properties of water, steam and air are built in.
Download
http://www.cuservices.net/DemoDownloads/PlossDemo.exe~
Pipe Network (Hardy Cross)
This program uses the iterative Hardy-Cross algorithm to determine the flow and pressure loss in each leg of a series-parallel pipe
network.
Download
http://www.cuservices.net/DemoDownloads/PipeNetworkDemo.exe~
Processing, Storage Tanks, Pressure Vessels, Mixing Systems
~
CerebroMix
CerebroMix is a unique PC-based program which encompasses all the functionality of the other Cerebro products, CerebroTank,
CerebroPV and CerebroMixLight. It is an indispensable tool for anyone involved in the evaluation and design of mixers in vertical
tanks, either pressurized or atmospheric. Using input data such as primary dimensions, fluid properties and certain desired mixing
objectives, the program will output full operating conditions, critical impeller speeds, liquid level gradation, solid suspension and all
system dimensions.
CerebroMix also allows the analysis of storage and process tanks, vertical or horizontal, pressurized or atmospheric. Using input
data such as principal dimensions, fluid density, material, desired tank shape (including heads) and support type, the software
calculates structural characteristics for both the tank and the support structure using ASME Section VIII, Division 1 and EN 13445
standards.
This software allows users and manufacturers of pressure vessels and mixers to check their equipment for various operating
conditions, in order to provide a full analysis of performance, as well as risk assessment.
The program produces output in the form of a Microsoft Word Document, with all data listed in tabular form, together with a scale
drawing of the tank and its support structure.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
CerebroPV
CerebroPV is an easy-to-use PC program to assist in the evaluation and design of vertical and horizontal storage tanks, running
either pressurized or at atmospheric conditions. Using input data such as principal dimensions, fluid density, material, desired tank
shape (including heads) and support type, the software calculates structural characteristics for both the tank and the support
structure using ASME Section VIII Division 1 standards.This software allows both users and manufacturers of pressure vessels to
check their equipment for various operating conditions, in order to provide a risk assessment. The program produces output in the
form of a Microsoft Word Document, with all data listed in tabular form, together with a scale drawing of the tank and its support
structure.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
CerebroTank
CerebroTank is an easy-to-use PC program to assist in the evaluation and design of vertical and horizontal storage tanks. Using
input data such as geometric dimensions, fluid density, support type, tank material and shape (including heads), the software
calculates structural characteristics for the tank and the supports (legs and saddles). Using the wall thicknesses provided by the
software, the user can select from a database of standard plate thicknesses; these thicknesses will be factored depending on the
degree of corrosiveness of the liquid. The program also gives flange thicknesses for the tank head, allowing for weld efficiency.
Download
http://www.engineering-software.com/prDemos/MixIILightDemo.exe~
Combustion
~
Enviropak
Enviropak is a combustion calculator and incinerator design package for organics. The user can choose from the resident database
of compounds or define new compounds. Recovery heat exchange, combustor sizing and destruction efficiency are all features of
this powerful software package. Included is a useful combustion properties estimation module. Output includes analysis of
combustion gases with computed temperature and residence times.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Combustion Analysis
This program calculates boiler efficiency using the heat loss method of the ASME Boiler Code PTC-4.1. The program accepts the
ultimate analysis of any fuel, % by weight for liquids and % by volume for gases. It performs a stochiometric analysis of the
combustion and calculates the individual losses, the quantities and types of gases produced, and the air flow required for the given
% excess air.
Download
اشکان فروتن
مدیر بازنشسته
Psychrometrics
~
Psychrometrics
(Metric and US units) This program provides Psychrometric properties of air given two properties as input values at a known
altitude (or atmospheric pressure). The properties are determined using the ideal gas law for the behavior of air. Once the
properties are determined, the point is indicated on the Psychrometric chart. Process lines can be connected between any two
know points, this will provide the user with the differences in moving from one point to the next. Additionally, this program will allow
the user to perform some basic HVAC calculations that depend on psychrometrics.
Download
~
Psychrometrics
This program calculates the properties of a mixture of air and water vapor such as used in HVAC applications. In addition, the
porgram calculates the results of the four most common types of heating and cooling psychrometrics processes.
Download
~
Heat Transfer
~
PHEdesign1.0
PHEdesign1.0 program for simulations of the plate heat exchanger. By setting our controlled variables and material properties, the
optimum plate dimensions and materials can be selected by the computer program. These are included rate of heat transfer, the
size of plate heat exchanger, and chevron angle (beta) between 25 to 65 degrees under single pass condition. Also this program is
capable of calculating the pressure drop in plate, from which the energy and material can be saved by decreasing the pressure
drop (decreasing horsepower per unit area) and increasing chevron angle.
Download
~
Space Heating Load
This program calculates the maximum heating load required in a space (single zone) so that a furnace can be sized. Heat transfer
coefficients are built in for many types of wall, floors, doors, windows, etc. Custom values can also be used. The heat needed for
infiltration & humidity control are also calculated. Final furnace sizes are tabulated with several values of efficiency.
~
Surface Condenser
This program, for analysis of turbine steam condensers, can either calculate the performance of a known condenser, or can
calculate the design requirements of a new condenser for a known steam load. The steam and condensate properties are built in.
Also a complete range of tube properties are built in. The cleanliness of a given condenser can be etermined quickly using a trial
and error method.
Download
~
Cooling Tower
Cooling Tower Analysis is a powerful, user friendly, program for the analysis of induced, mechanical-draft, counterflow cooling
towers. The program can be used for the analysis of existing towers or for the preparation of specifications for new towers.
Download
~
Steam Heater
This program calculates the performance of a steam, shell-and-tube heat exchanger of known construction using rigorous
formulations. Steam and water properties are built in. The type of fouling can be specified. The shell-side fluid is always steam. The
tube side fluid can be any non-condensing fluid.
~
Heat Recovery Steam Generator
This program calculates the amount of steam that can be generated by a fired or unfired waste heat boiler (Heat Recovery Steam
Generator). The steam and condensate properties are built in. The program first calculates a design mode and then an "off-
performance mode" for changed conditions. Note: the purpose of this progam is to predict the amount of steam that can be
generated from a waste heat source. The program does not calculate the square feet of each section of the HRSG. Instead it
calculates the value of U x A.
~
Insulation Economics
This program calculates the heat loss and surface temperature of an insulated pipe of specified diameter and internal temperature.
It then calculates the present worth cost, $/foot, to own and operate each insulated system. This allows the user to select the
optimum insulation thickness for each pipe based either on the cost of the insulation and heat loss or on the maximum acceptable
surface temperature. Four types of insulation are supported. Pipe sizes through 36" are included. Three layers of insulation are
supported ranging in thickness from 0 to 10".
Download
~
Shell & Tube Heat Exchanger
Heat Exchanger Performance is a powerful, user friendly, program for the analysis of two types of Heat Exchangers: Shell & Multi-
Tube Exchangers, and Double Pipe Exchangers. In either case, the tubes are of the bare-tube type. The program will analyze the
performance of a known heat exchanger: Given the flows and inlet temperatures of the Tube-side fluid and the Shell-side fluid, the
program will predict the exit temperatures of both fluids and the total heat exchanged.
Download
~
~
Psychrometrics
(Metric and US units) This program provides Psychrometric properties of air given two properties as input values at a known
altitude (or atmospheric pressure). The properties are determined using the ideal gas law for the behavior of air. Once the
properties are determined, the point is indicated on the Psychrometric chart. Process lines can be connected between any two
know points, this will provide the user with the differences in moving from one point to the next. Additionally, this program will allow
the user to perform some basic HVAC calculations that depend on psychrometrics.
Download
~
Psychrometrics
This program calculates the properties of a mixture of air and water vapor such as used in HVAC applications. In addition, the
porgram calculates the results of the four most common types of heating and cooling psychrometrics processes.
Download
~
Heat Transfer
~
PHEdesign1.0
PHEdesign1.0 program for simulations of the plate heat exchanger. By setting our controlled variables and material properties, the
optimum plate dimensions and materials can be selected by the computer program. These are included rate of heat transfer, the
size of plate heat exchanger, and chevron angle (beta) between 25 to 65 degrees under single pass condition. Also this program is
capable of calculating the pressure drop in plate, from which the energy and material can be saved by decreasing the pressure
drop (decreasing horsepower per unit area) and increasing chevron angle.
Download
~
Space Heating Load
This program calculates the maximum heating load required in a space (single zone) so that a furnace can be sized. Heat transfer
coefficients are built in for many types of wall, floors, doors, windows, etc. Custom values can also be used. The heat needed for
infiltration & humidity control are also calculated. Final furnace sizes are tabulated with several values of efficiency.
~
Surface Condenser
This program, for analysis of turbine steam condensers, can either calculate the performance of a known condenser, or can
calculate the design requirements of a new condenser for a known steam load. The steam and condensate properties are built in.
Also a complete range of tube properties are built in. The cleanliness of a given condenser can be etermined quickly using a trial
and error method.
Download
~
Cooling Tower
Cooling Tower Analysis is a powerful, user friendly, program for the analysis of induced, mechanical-draft, counterflow cooling
towers. The program can be used for the analysis of existing towers or for the preparation of specifications for new towers.
Download
~
Steam Heater
This program calculates the performance of a steam, shell-and-tube heat exchanger of known construction using rigorous
formulations. Steam and water properties are built in. The type of fouling can be specified. The shell-side fluid is always steam. The
tube side fluid can be any non-condensing fluid.
~
Heat Recovery Steam Generator
This program calculates the amount of steam that can be generated by a fired or unfired waste heat boiler (Heat Recovery Steam
Generator). The steam and condensate properties are built in. The program first calculates a design mode and then an "off-
performance mode" for changed conditions. Note: the purpose of this progam is to predict the amount of steam that can be
generated from a waste heat source. The program does not calculate the square feet of each section of the HRSG. Instead it
calculates the value of U x A.
~
Insulation Economics
This program calculates the heat loss and surface temperature of an insulated pipe of specified diameter and internal temperature.
It then calculates the present worth cost, $/foot, to own and operate each insulated system. This allows the user to select the
optimum insulation thickness for each pipe based either on the cost of the insulation and heat loss or on the maximum acceptable
surface temperature. Four types of insulation are supported. Pipe sizes through 36" are included. Three layers of insulation are
supported ranging in thickness from 0 to 10".
Download
~
Shell & Tube Heat Exchanger
Heat Exchanger Performance is a powerful, user friendly, program for the analysis of two types of Heat Exchangers: Shell & Multi-
Tube Exchangers, and Double Pipe Exchangers. In either case, the tubes are of the bare-tube type. The program will analyze the
performance of a known heat exchanger: Given the flows and inlet temperatures of the Tube-side fluid and the Shell-side fluid, the
program will predict the exit temperatures of both fluids and the total heat exchanged.
Download
~
اشکان فروتن
مدیر بازنشسته
Physical Properties and Steam Tables
~
TriMAX
Tri MAX™ is a powerful software resource for the practicing engineer, chemist, or student. It is your best source of data. Through
the use of menus: data and functionality are put at the finger tips of the power user. Tri MAX™ provides data such as periodic table,
steam tables, heat capacities, critical values, viscosities, diffusion coefficients, thermal conductivities. Math functions are also
provided, such as linear regression, quadratic equation, curve fitting, and a calculator that goes far beyond the standard calculators
available for Microsoft™ Platforms.
Download
http://www.engineering-software.com/prDemos/27530.findrex.zip~
zCalc
Compressibility calculator for natural gas mixtures using the American Gas Association methodology from their AGA-8 Report. The
software quickly takes a mixture of natural gas (up to 20 components) and calculates the compressibility, molar density, mass
density, base compressibility and supercompressibility.
Download
http://www.engineering-software.com/prDemos/ZCALCSETUP.EXE~
Steampak
Steampak is a high-accuracy steam and water physical properties database and process calculator. Steampak's algorithm is
based on the equation of state of Keenan, Keyes, Hill and Moore which is the basis of the published International Steam Tables. The
process calculator allows calculation of steam compression and expansion processes at user-selected efficiencies including
isentropic & adiabatic expansions and flash calculations.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Chempak
Chempak is a powerful physical properties software package giving details of thermodynamic and transport properties of over 600
common organic and inorganic compounds as functions of temperature and pressure. All common chemical engineering constant
and variable properties are included. Liquid and vapor phases are covered as well as saturated and unsaturated states. Mixtures of
database compounds and new liquids can be defined. Numerical and graphical output are supported. Chempak links to Chempak II -
Madison's user-defined compounds software package.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Chempak II
Chempak II enables the user to define the thermodynamic and transport properties of new compounds not already in the Chempak
database. From as little information as the compound chemical formula, the user can build up a complete profile of the compound
properties and add the compound to the Chempak database for future recall and calculation. Chempak II allows the user to enter
known property data and also provides sophisticated estimation methods where no data is available. Chempak II provides the
perfect companion software to Chempak.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Steam Properties
This program calculates the properties of superheated, saturated, or wet steam. In addition it calculates the properties of
saturated water.
~
Steam Tables
(Metric and US units) This program provides the thermodynamic properties of water using IFC formulation for industrial use.
Knowing any two properties, the user is able to completely define the properties of water/steam. Unlike most steam table programs,
this program also provides the user with the point's location on the T-S diagram. Multiple points can be connected by a line, defining
the user's process system. It even gives you the steam quality.
Download
http://www.engineering-software.com/prDemos/steademo.exe~
Physical Properties
Engineering Software has developed a new Windows based software package, Physical Properties, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of power and propulsion systems. It should provide the user with the opportunity to more quickly, easily and effectively
do his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Steam Approximations
Engineering Software has developed a new Windows based software package, Steam Approximations, that quickly, easily and
reliably calculates thermodynamic and transport properties of steam for both saturated and superheated areas.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Physical Properties and Steam Approximations
Engineering Software has developed a new Windows based software package, Physical Properties and Steam Approximations,
that quickly, easily and reliably calculates thermodynamic and transport properties of gaseous, liquid and solid species and steam
approximations for both saturated and superheated areas.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Physical Properties Spreadsheet
Physical Properties Spreadsheet quickly, easily and reliably calculates thermodynamic and transport properties of a few gaseous,
liquid and solid species.
This spreadsheet should prove to be a good tool for those who are involved at various levels with design, operation and
management of power and propulsion systems. It should provide you with the opportunity to more quickly, easily and effectively do
your work, explore more options, save time and give more confidence in carrying out your calculations.
~
Economics
~
Cogeneration Economics
This program calculates the the return on investment, present worth, and payback for a power plant that produces electrical power
or produces both electrical power and heat energy.
Download
http://www.cuservices.net/DemoDownloads/CogenDemo.exe~
~
TriMAX
Tri MAX™ is a powerful software resource for the practicing engineer, chemist, or student. It is your best source of data. Through
the use of menus: data and functionality are put at the finger tips of the power user. Tri MAX™ provides data such as periodic table,
steam tables, heat capacities, critical values, viscosities, diffusion coefficients, thermal conductivities. Math functions are also
provided, such as linear regression, quadratic equation, curve fitting, and a calculator that goes far beyond the standard calculators
available for Microsoft™ Platforms.
Download
http://www.engineering-software.com/prDemos/27530.findrex.zip~
zCalc
Compressibility calculator for natural gas mixtures using the American Gas Association methodology from their AGA-8 Report. The
software quickly takes a mixture of natural gas (up to 20 components) and calculates the compressibility, molar density, mass
density, base compressibility and supercompressibility.
Download
http://www.engineering-software.com/prDemos/ZCALCSETUP.EXE~
Steampak
Steampak is a high-accuracy steam and water physical properties database and process calculator. Steampak's algorithm is
based on the equation of state of Keenan, Keyes, Hill and Moore which is the basis of the published International Steam Tables. The
process calculator allows calculation of steam compression and expansion processes at user-selected efficiencies including
isentropic & adiabatic expansions and flash calculations.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Chempak
Chempak is a powerful physical properties software package giving details of thermodynamic and transport properties of over 600
common organic and inorganic compounds as functions of temperature and pressure. All common chemical engineering constant
and variable properties are included. Liquid and vapor phases are covered as well as saturated and unsaturated states. Mixtures of
database compounds and new liquids can be defined. Numerical and graphical output are supported. Chempak links to Chempak II -
Madison's user-defined compounds software package.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Chempak II
Chempak II enables the user to define the thermodynamic and transport properties of new compounds not already in the Chempak
database. From as little information as the compound chemical formula, the user can build up a complete profile of the compound
properties and add the compound to the Chempak database for future recall and calculation. Chempak II allows the user to enter
known property data and also provides sophisticated estimation methods where no data is available. Chempak II provides the
perfect companion software to Chempak.
Download
http://www.engineering-software.com/prDemos/Mtsdemo.exe~
Steam Properties
This program calculates the properties of superheated, saturated, or wet steam. In addition it calculates the properties of
saturated water.
~
Steam Tables
(Metric and US units) This program provides the thermodynamic properties of water using IFC formulation for industrial use.
Knowing any two properties, the user is able to completely define the properties of water/steam. Unlike most steam table programs,
this program also provides the user with the point's location on the T-S diagram. Multiple points can be connected by a line, defining
the user's process system. It even gives you the steam quality.
Download
http://www.engineering-software.com/prDemos/steademo.exe~
Physical Properties
Engineering Software has developed a new Windows based software package, Physical Properties, that quickly, easily and reliably
calculates thermodynamic and transport properties of gaseous, liquid and solid species.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of power and propulsion systems. It should provide the user with the opportunity to more quickly, easily and effectively
do his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Steam Approximations
Engineering Software has developed a new Windows based software package, Steam Approximations, that quickly, easily and
reliably calculates thermodynamic and transport properties of steam for both saturated and superheated areas.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Physical Properties and Steam Approximations
Engineering Software has developed a new Windows based software package, Physical Properties and Steam Approximations,
that quickly, easily and reliably calculates thermodynamic and transport properties of gaseous, liquid and solid species and steam
approximations for both saturated and superheated areas.
This software package should prove to be a good tool for those who are involved at various levels with design, operation and
management of energy conversion systems. It should provide the user with the opportunity to more quickly, easily and effectively do
his/her work, explore more options, save time and give more confidence in carrying out engineering calculations.
Download
http://www.engineering-software.com/prDemos/engware32-7d.exe~
Physical Properties Spreadsheet
Physical Properties Spreadsheet quickly, easily and reliably calculates thermodynamic and transport properties of a few gaseous,
liquid and solid species.
This spreadsheet should prove to be a good tool for those who are involved at various levels with design, operation and
management of power and propulsion systems. It should provide you with the opportunity to more quickly, easily and effectively do
your work, explore more options, save time and give more confidence in carrying out your calculations.
~
Economics
~
Cogeneration Economics
This program calculates the the return on investment, present worth, and payback for a power plant that produces electrical power
or produces both electrical power and heat energy.
Download
http://www.cuservices.net/DemoDownloads/CogenDemo.exe~
اشکان فروتن
مدیر بازنشسته
Flash Tank Economics
This program calculates the economic results that can be achieved by using a flash tank and a heat exchanger to recover boiler
blowdown. The program calculates the amount of flash steam and saturated condensate that will separate when a high pressure,
high temperature water steam is flashed in a tank of lower pressure. It then assigns a dollar value to each of the two components
based on the value of fuel, boiler efficiency, etc.
Download
http://www.cuservices.net/DemoDownloads/FlashTankDemo.exe~
Insulation Economics
This program calculates the heat loss and surface temperature of an insulated pipe of specified diameter and internal temperature.
It then calculates the present worth cost, $/foot, to own and operate each insulated system. This allows the user to select the
optimum insulation thickness for each pipe based either on the cost of the insulation and heat loss or on the maximum acceptable
surface temperature. Four types of insulation are supported. Pipe sizes through 36" are included. Three layers of insulation are
supported ranging in thickness from 0 to 10".
Download
This program calculates the economic results that can be achieved by using a flash tank and a heat exchanger to recover boiler
blowdown. The program calculates the amount of flash steam and saturated condensate that will separate when a high pressure,
high temperature water steam is flashed in a tank of lower pressure. It then assigns a dollar value to each of the two components
based on the value of fuel, boiler efficiency, etc.
Download
http://www.cuservices.net/DemoDownloads/FlashTankDemo.exe~
Insulation Economics
This program calculates the heat loss and surface temperature of an insulated pipe of specified diameter and internal temperature.
It then calculates the present worth cost, $/foot, to own and operate each insulated system. This allows the user to select the
optimum insulation thickness for each pipe based either on the cost of the insulation and heat loss or on the maximum acceptable
surface temperature. Four types of insulation are supported. Pipe sizes through 36" are included. Three layers of insulation are
supported ranging in thickness from 0 to 10".
Download
Similar threads
Similar threads
-
برنامه نویسی مسائل ریاضی پیشرفته با ویژوال بیسیک- شروع شده توسط امیدی
- پاسخ ها: 0
-
-
-
-